Shop Screen Protectors
Shop Cases
Shop Accessories
Replacements
Support
Replace your screen protector
Register a new screen protector
Register a new case
More info
WELCOME TO OUR STORE
DOWNLOAD THE INSTALLATION INSTRUCTIONS PDF
- PRO TIP 1 - Before you begin installation, make sure the device screen is completely dust-free. Dust, hair and other small particles can cause a permanent bubble under the protector. Use the included microfiber cleaning cloth and dust removal strips to remove any dust before installation.
- PRO TIP 2 - If you do get a piece of dust underneath the protector, carefully use your fingernail to lift the closest edge and use the dust removal strip on the sticky side of the protector to grab and remove the dust.
HAVE QUESTIONS?
BodyGuardz SpyGlass Express Align® Method
Thank you for purchasing SpyGlass by BodyGuardz for your smartphone! After you complete the installation process detailed in this video, you will enjoy unmatched protection from impacts, scratches, and prying eyes. Included in the box are a cleaning cloth, dust removal stickers, the Express Align tray, and the SpyGlass tempered glass screen protector. Make sure you have these on hand before you begin. First, turn off your device, remove your case, and place your device on a clean, flat surface. To prevent dirt or dust from getting trapped beneath the protector, clean your device’s screen with the cleaning cloth provided. Once you have removed all dirt and dust from your device, pick up the Express Align tray and peel off the release liner to expose the adhesive side of the protector. Then, place the tray on top of your device. Use the camera and speaker to align the top portion of the tray, and the home button to align the bottom. Firmly press and hold the protector down with your finger through the opening in the tray. Using your other hand, pull the tray away from the protector. Use the dust removal stickers if any dust particles become trapped between the protector and your device during the installation. Carefully lift up the corner of the protector closest to the particle, then place the sticky side of the strip against the speck of dust and pull the dust sticker straight out. Use the included cleaning cloth to push out any air bubbles. Some air bubbles may take 24-48 hours to disappear, but you should be able to push most of them out. Finally, peel off the cap sheet from the surface of the protector. Congratulations on installing SpyGlass by BodyGuardz! If you have any questions, please email us at support@bodyguardz.com, or send us a message on Facebook.
BodyGuardz SpyGlass Suction Cup Method
Thank you for purchasing SpyGlass by BodyGuardz for your smartphone! After you complete the installation process detailed in this video, you will enjoy unmatched protection from impacts, scratches, and prying eyes. Included in the box are a cleaning cloth, dust removal stickers, a suction cup, and the SpyGlass tempered glass screen protector. Make sure you have these on hand before you begin. Let’s get started. First, turn off your device, remove your case, and place your device on a clean, flat surface. To prevent dirt or dust from getting trapped beneath the protector, clean your device’s screen with the cleaning cloth provided. Once you have removed all dirt and dust from your device, attach the suction cup to the front of the protector, which is covered with a clear cap sheet that has tabs on both the top and bottom. Next peel off the release liner to expose the adhesive. Holding on to the suction cup and edges of the protector, align the protector over your device. We recommend using the speaker and home button as a guide to ensure perfect alignment. When you have aligned the protector, lay it down gently on your device. While pressing down on the center of the screen, carefully remove the suction cup. Use the dust removal stickers if any dust particles become trapped between the protector and your device during the installation. Carefully lift up the corner of the protector closest to the particle, then place the sticky side of the strip against the speck of dust and pull the dust sticker straight out. Use the included cleaning cloth to push out any air bubbles. Some air bubbles may take 24-48 hours to disappear, but you should be able to push most of them out. Finally, peel off the cap sheet from the surface of the protector. Congratulations on installing SpyGlass by BodyGuardz! If you have any questions, please email us at support@bodyguardz.com, or send us a message on Facebook.
